magnetmotortv asked:
reveals some technical truths about Free Energy Systems. Discovering how this technology works and being able to benefit from it is important to every one on earth. Being able to create electricity from magnetic forces with a trans-portable generator will change life on earth forever. Green Motor Project Video 4 Free Energy Technologies. Produced By www.MrBigTV.Com 310-266-7574 This experiment used 1/2 inch X 1 Inch N52 Neodinium Magnets. If the magnets where any bigger you could get hurt …
17 Comments
August 20th, 2009 at 11:14 pm
hello i made a visual aids mistake on this video so it will be redone ASAP and fixed. I cant believe not one of my students noticed the mistake. The paper fields should have been drawn different
August 21st, 2009 at 3:35 am
just try to help you out…
shared interest
August 21st, 2009 at 10:40 pm
right on Bro Love your work but ya might need less caffiene just kidding. i see you look like an American in America… Am I right?
August 23rd, 2009 at 12:35 am
i wonder if they sell crack in his country? Look at all these comments! Someone got very excited… Looks Good Bro maybe i will go back to guzzling caffiene so i can keep up with you. Do you get excited easily?
August 25th, 2009 at 7:39 pm
i looked at the rotar design again
From Dario Busch Magnetic Motor Free Energy Open Source 2
has 17 rotor poles
21.17647 deg apart?
stator feild has 10 per side but i assuming 11 could fit
so 180/11= 16.36 deg per side
August 26th, 2009 at 11:21 pm
another observation, the magnets on the rotar and stator are manchined to give a skewed plan…is this a way to direct the feild?… make the push pull force stronger
in some way?
August 28th, 2009 at 12:55 am
do a tube search:
mini magnet power generator motor free energy overunity Switserland magnetic turbine off the grid
it was a interesting idea
August 30th, 2009 at 5:53 pm
use your simple motor wheel design
but use earth magnets…
i have been messing around with
the idea of 2 rotationg (small 4 pole n/s )stator hubs on bearing …to push and pull the rotor…
August 31st, 2009 at 1:48 am
i would strong remcomment 5-6 laminated
rare earth magnets for each of the rotor poles total 6 poles max
then creater a simple 3 phase stator field
with 3-4 magnet per field but set them up
with split n/s magnet not sure if a square magnet will work better..
try my shielding idea on these laminated stator split magnet n/s pole,,,
and use you logic u developed
levaging the push pull action with the shield and skew design of magnets feilds
August 31st, 2009 at 7:34 am
i think your very close, a couple observation, the only way I see this will work
is with earth magnets, the other point youneed to simplify the motor and rotor.
Keep as many few magnets as need, reducingand counter affects, untill we can
understand what required, for shielding
September 1st, 2009 at 1:55 am
right on bro
September 1st, 2009 at 5:33 am
the magnets must alternate in some way for it to work.i observed with hand observations that if the magnets in the stator are magnetized through the diameter they pull together instead of push apart and still push apart when they are supposed to so i simply never could afford to continue with the experiments do to no funding from anyone but me… It Could Work Is What I Still Believe
September 4th, 2009 at 3:39 am
your frist magnet is one soild magnet…..the secound magnet sheilding was a seris of magnet attacted a steel bar is a good idea but I noticed your magnents are laminated in layers
thus you can redirect the eddie current into your sheliding as needed
September 5th, 2009 at 2:47 pm
keep up the good work
i noticed in prerendev sketch.. his stator
has split pole magnets s/n s/n s/n and only n magnets on the rotor
is this another key?
September 7th, 2009 at 7:27 pm
cool idea bro
September 8th, 2009 at 4:40 am
That’s creative…
September 8th, 2009 at 11:31 am
You could try a gradient ramp at the end of the track, to see if the ball can jump up and out with its own inertia.